MAKE IT YOURS
Superior MotionProtect Plus G3.
Wireless PIR motion detector with an additional K-band microwave sensor and anti-masking system
Standards and certifications
Superior MotionProtect Plus G3 Jeweller · MPP.G3.J. Manufacturer-listed marks; regional and installation conditions apply.
Two sensors. Wireless G3 protection.
Superior MotionProtect Plus G3 Jeweller combines PIR motion detection with K-band microwave verification to help distinguish movement from thermal interference. Anti-masking and monitored mounting protect the detector itself. A compatible Ajax system manages alarms and settings over radio, with Wings support for firmware updates.
Key features. At a glance.
Ajax product information ↗ · Superior MotionProtect Plus G3 Jeweller specifications ↗
Protection in real places.
See the room and the approach below.
Up to 15 m of motion detection
The PIR sensor and mirror optics detect indoor movement at up to 15 m when installed at 2.4 m. The exact specification lists a reduced blind zone of 30 cm, helping detect a crawling person close to the device.
Detection depends on position and a clear view. Walk-test the actual intrusion path and nearby floor area after installation.
A second sensor verifies movement.
PIR detection, checked by K-band
The PIR sensor detects changes in infrared radiation; the microwave sensor verifies that movement is present. The combined decision helps filter thermal interference, such as air flows and heating effects, before the detector reports an alarm.
This is motion verification, not photo or video verification. The detector has no camera.
Adapt detection to the room.
SmartDetect and three sensitivity levels
SmartDetect evaluates the moving thermal pattern. Choose Low, Normal or High sensitivity in the app, then confirm the result with the Detection Zone Test rather than relying on the setting alone.
Compensate for changing temperature
Temperature compensation adjusts PIR readings as ambient temperature changes. It works within the specified −10 to +40 °C indoor operating range.
Cover the room, including the approach below.
Position the mirror optics across the entry path
Install indoors at 2.4 m, looking across the likely movement path. The mirror optics provide a 90° horizontal and 71° vertical field of view. Keep furniture, plants and glass outside the monitored view, then walk-test the full room.
Choose G3 with its detection priorities in mind
These detectors do not support pet immunity. Their reduced blind zone is intended to recognise movement close below the device, including a crawling person. Plan the protected area so animals cannot enter it while armed.
Do not apply the 20 kg / 50 cm pet-immunity limits of other MotionProtect models to these G3 devices.
Use in a suitable indoor environment
The operating range is −10 to +40 °C with humidity up to 75%. Avoid direct sunlight, heat sources and obstructions close to the optics. An IP30 enclosure is for indoor use; check detection again after changing the room layout.
Notice when someone blocks the view.
Keep anti-masking enabled and calibrated
The dedicated sensor detects attempts to obstruct or cover the optics, including material placed over the detector or paint on its window. With anti-masking enabled, this protection also operates while the system is disarmed.
Calibrate in the final mounting position with a clear field of view. Recalibrate after moving the detector or when the app reports a calibration fault, and test masking detection before handover.
Protect the mounting as well as the room.
Three tamper switches and a monitored lock
Two rear tamper switches supervise the mounting, while a third monitors the SmartBracket lock. Wall and side mounting depend on the correct fixing points and intact breakaway sections. Lock the detector in place and test removal events after installation.
A tamper alert identifies interference; it does not physically prevent damage. Confirm that the app and any monitoring service receive the event.
Check the detector as well as its connection.
Supervise the built-in sensors
Automatic self-tests check the PIR and masking sensors and the microwave sensor. Faults appear in the app, and a manual test is available during commissioning and maintenance.
Secure events. Wireless firmware updates.
Superior Jeweller and Wings
Superior Jeweller carries alarms, events and commands. Wings handles firmware updates. Encryption, authentication and frequency hopping protect communication; the supported radio behaviour depends on the hub and other devices in the system.
Requires a compatible hub with OS Malevich 2.40 or later. The manual states up to 3,000 m in open space; the actual range depends on the hub, walls and interference. The current specification still marks the Jeweller maximum as awaiting confirmation.
Grade 3 starts with the complete system.
Keep the radio protection consistent
Superior Jeweller provides encrypted communication and enhanced frequency hopping when every connected wireless device supports it. Adding a regular Jeweller device changes the system’s radio behaviour and limits the system to Grade 2.
Grade 3 is not guaranteed by buying one G3 device. An accredited Ajax partner must check the hub, every connected device, radio settings, installation and monitoring requirements together. Check the enhanced-hopping status in the app.
Plan for battery service.
Up to 4 years on four CR123A batteries
Four pre-installed replaceable batteries power the detector. Low-battery warnings help arrange service. Follow the exact replacement procedure and test the detector afterwards.
The 4-year figure is a calculated maximum. Polling, radio conditions, events and firmware updates affect actual battery life.
Position, pair and test the wireless detector.
Fix and lock SmartBracket
An accredited Ajax partner checks the position and level before fixing the panel to the wall or corner. Secure the specified tamper fixing points, then close the monitored lock. Adhesive mounting is only for temporary positioning.
Find the right motion detector.
Compare indoor, outdoor and curtain detectors across Baseline and Superior. See what changes for the place you protect, alarm photos, animals and installation.
Compare motion detectors →Every detail, in one place.
Communication
- Superior Jeweller data transfer protocol
- Proprietary wireless protocol for transmitting commands, alarms, and events. An upgraded version of the Jeweller radio protocol for Ajax Superior devices, ensuring compliance with Grade 3 (EN 50131). Key features: Two-way communication. Advanced sabotage protection. Enhanced block encryption with a dynamic key. Instant notifications. Remote control and configuration in Ajax apps.
- Frequency bands
- 865.0–868.0 MHz 868.0–868.6 MHz 868.7–869.2 MHz 869.4–869.65 MHz
- Maximum effective radiated power (ERP)
- up to 20 mW Automatic power control to reduce power consumption and radio interference.
- Radio signal modulation
- GFSK
- Radio communication range
- up to 3,000 m (manufacturer confirmation pending) Between the device and a hub (or a range extender) in an open space. The maximum range depends on the hub model.
- Encrypted communication
- All stored and transmitted data is protected with advanced encryption, ensuring both confidentiality and integrity.
- Frequency hopping
- To prevent radio interference and jamming.
- Wings communication technology
- Proprietary wireless communication technology for uploading firmware updates. Key features: Two-way communication. Advanced sabotage protection. Block encryption featuring a dynamic key. Data packet reload in case of transmission errors. Data packets delivery check.
- Frequency bands
- 865.0–868.0 MHz 868.0–868.6 MHz 868.7–869.2 MHz 869.4–869.65 MHz
- Radio communication range
- up to 3,000 m Between the device and a hub (or a range extender) in an open space. The maximum range depends on the hub model.
- Encrypted communication
- All stored and transmitted data is protected with advanced encryption, ensuring both confidentiality and integrity.
- Frequency hopping
- To prevent radio interference and jamming.
Detection
- Sensitive element
- PIR sensor microwave sensor K-band microwave sensor to prevent false alarms caused by thermal interference. Operation frequency: Manufacturer confirmation pending.
- Motion detection distance
- up to 15 m When installed at a height of 2.4 m.
- Reduced blind zone
- up to 30 cm Detects a crawling person at a distance of 30 cm from the detector.
- Motion detection angles
- horizontal — 90° vertical — 71°
- Motion detection speed
- Manufacturer confirmation pending The direction of the detector sensors should be perpendicular to an alleged intrusion path into the facility.
- Sensitivity
- 3 levels Adjusted by a PRO or a user with admin rights in the Ajax app
- False alarm prevention
- SmartDetect Software algorithm.
- Temperature compensation
- Effective motion detection at temperatures from −10 °C to +40 °C.
Sabotage protection
- Tamper alarm
- 3 tampers Notifications on attempts to detach the detector from the surface or unlock the SmartBracket lock and remove the detector from the mounting panel.
- Protection against spoofing
- device authentication
- Anti-masking system
- detects attempts to block the detector view
- Lock for SmartBracket
- To secure the detector on SmartBracket.
- Communication loss detection
- after 36 s Detection time depends on the Jeweller/Fibra settings.
Power supply
- Batteries
- 4 × CR123A 3 V⎓ lithium battery Pre-installed.
- Type
- Type C
- Detector’s operating voltage range
- 3.6−6.0 V⎓
- Detector’s nominal operating voltage
- 6 V⎓
- Quiescent detector’s current consumption at nominal voltage
- 40 μA
- Maximum detector’s current consumption at nominal voltage
- 96 mA
- Full battery capacity
- 3,100 mAh
- Low battery voltage
- 5.2 V⎓
- Low battery recovery voltage
- 5.4 V⎓
- End-of-life battery voltage
- 3.6 V⎓ The device is switched off.
- End-of-life battery capacity
- 200 mAh
- Calculated battery life
- up to 4 years
- Manufacturer
- Panasonic
Enclosure
- Dimensions
- 135 × 66 × 60 mm
- Weight of the white device
- 315 g
- Weight of the black device
- 310 g
- Operating temperature range
- from −10 °C to +40 °C
- Operating humidity
- up to 75%
- Protection class
- IP30
What’s in the box
- Superior MotionProtect Plus G3 Jeweller
- SmartBracket mounting panel
- 4 × CR123A battery (pre-installed)
- Installation kit
- Quick start guide
For your installation
- Selected as part of an installer-reviewed security or automation project.
- Confirm the supported control panel, device software and regional radio version; test coverage at the final installation position.
- It is recommended to install the detector at a height of 2.4 m.
- The pet immunity feature is not available for this device.
- The device is designed for indoor use only.
Product documents.
Find the right protection.
Superior MotionProtect G3 Jeweller
Check whether PIR detection or additional microwave verification suits the room.
Superior MotionProtect Plus G3 Fibra
Explore the corresponding wired or wireless model and its own requirements.