MAKE IT YOURS
MultiTransmitter.
Wireless module to integrate up to 18 third-party devices into an Ajax system
Standards and certifications
MultiTransmitter Jeweller · MTR.Y.J. Manufacturer-listed marks; regional and installation conditions apply.
A new system around suitable existing wiring.
MultiTransmitter Jeweller brings eighteen wired zones into an Ajax system, with names, rooms and meaningful notifications for connected devices. Mains power, shared detector power outputs and a separately selected backup battery support a complete installation. Supervised wiring options depend on the exact hardware and hub, allowing an installer to plan the upgrade around the circuits already in place.
Key features. At a glance.
18 wired zones
Individual device or circuit inputs
NC / NO / EOL
Supported contact schemes
2EOL and 3EOL1
Separate circuit states
15 event types2
Names and rooms in each event
Up to 400 m3
Wired signal distance
Up to 2,000 m4
Jeweller radio in open space
Three power lines5
10.5–15 V DC output
100–240 V AC
Main power supply
12 V backup battery6
Space for up to 7 Ah
Two tampers
Opening and wall removal
Remote setup
Configuration in Ajax apps
IP40 / IK067
Indoor enclosure
- 1Needs compatible module hardware with firmware 2.13.0 or later. Hub OS 2.13 or later; Hub (4G) needs 2.28. Hub (2G) does not support these schemes. Old module hardware cannot be upgraded.
- 2Available functions depend on the hub and selected zone mode.
- 3Specified with 0.22 mm² copper-clad aluminium signal conductor; check the actual circuit.
- 4Walls, metal and interference reduce usable range.
- 5Up to 1 A total across all outputs, not per line.
- 6Battery is sold separately. Backup duration depends on the complete connected load.
- 7For the listed cased model, −10°C to +40°C.
Ajax product information ↗ · MultiTransmitter Jeweller specifications ↗
MultiTransmitter Jeweller
Every detail has a purpose.
Explore the function, installation and system requirements of MultiTransmitter Jeweller.
Loading detail…
Keep suitable wiring. Modernise its reporting.
Control the combined system in Ajax apps
MultiTransmitter brings existing wired devices into an Ajax system through eighteen input zones. Users receive named events, while professionals can configure the system on site or remotely.
Each old detector still needs a compatible signal, sound wiring and the correct power supply. The module does not repair or modernise the sensing element itself.
Match each wired zone to its task.
Different devices, meaningful events
Compatible motion sensors, opening contacts, panic buttons, gas or water sensors and other devices can report through the module. Assign the appropriate event type and room for each zone.
Multiple contacts on a shared zone are reported as that zone. The connected load, wiring scheme and hub capacity determine the complete installation.
Read alarm, tamper and fault separately.
NC, NO and supervised EOL circuits
Supported hardware accepts NC, NO, EOL, 2EOL and 3EOL wiring. Supervised circuits let the system distinguish states such as an alarm, tamper, a cut cable or short circuit, according to the connection used.
2EOL/3EOL requires module firmware 2.13.0 or later and a compatible hub with OS Malevich 2.13 or later. Hub (4G) requires 2.28; Hub (2G) does not support 2EOL/3EOL. Older module hardware cannot gain these functions through a firmware upgrade.
Measure the installed circuit
On the newer hardware, each EOL resistor can be 1–15 kΩ, with total resistance up to 30 kΩ. The PRO app helps measure the circuit and configure its states.
Use the limits for the actual hardware revision; older units have different resistor ranges. Up to 400 m is specified with a 0.22 mm² copper-clad aluminium signal conductor. Cable resistance and power drop still require checking.
Know which zone needs attention.
Names, rooms and event types
Configure a descriptive name and room for every input. Notifications and monitoring codes can then explain both the event and where it came from.
Fifteen event types are listed for the current model. Features depend on the selected zone mode and compatible hub software.
Use a verified input to trigger a response.
Configured system actions
An alarm from a connected device can trigger an agreed Ajax automation scenario, such as switching a light. Scheduling and compatible KeyArm input settings can also form part of the system.
MultiTransmitter itself has no control relay output. Any switching action needs a separate compatible automation device and a tested scenario.
Size power and backup for the whole installation.
Mains input and shared device power
The module operates from 100–240 V AC. It supplies connected devices at 10.5–15 V DC through three lines, with a combined maximum load of 1 A.
The fire-detector line supports the documented power-reset procedure. Use only the supported detector connection and check the complete current budget.
A separately selected 12 V battery
A compatible battery up to 7 Ah can maintain the module and attached devices after mains loss. It is not included.
For a 7 Ah battery, the specification gives at least seven hours at a 1 A load. For twelve or twenty-four hours, the maximum load is 0.55 A or 0.28 A respectively. Calculate the required duration for the complete connected load.
A secure link to your system.
Jeweller communication
Encrypted two-way communication carries commands, alarms and device status between the device and its compatible Ajax hub or assigned range extender.
Up to 2,000 m in open space. Walls, metal and other obstacles reduce usable coverage. Check signal strength at the installation position and use equipment for the same radio-frequency region.
Use the wiring where radio cannot reach.
Place the module where its hub link is reliable
The module can remain in a suitable radio position while wired zones reach other rooms. A compatible Ajax range extender can also improve its link to the hub.
The 400 m cable limit and open-space radio distance describe different parts of the system. Test both, and keep the module indoors at −10°C to +40°C.
Watch the cabinet and the connected circuits.
Enclosure and line supervision
Two tampers monitor opening of the lid and detachment from the wall. Supported EOL circuits also report wiring faults; the hub supervises the module’s radio link.
Circuit fault detection depends on the selected wiring type. Radio-loss timing depends on polling settings.
Commission every reused zone.
A complete installation check
An installer checks the existing wiring, mounts the enclosure, pairs by QR code and configures each zone. Test every alarm, restoration, tamper, cable fault and mains-failure response before handing over the system.
Follow the mains-power and battery procedures in the exact manual. Indoor enclosure: IP40 and IK06 for the listed model.
Find the right wired integration module.
Keep suitable wired detectors when moving to Ajax. Compare signal inputs, detector power and whether the module can also control equipment.
Compare wired integration →Every detail, in one place.
Communication
- Jeweller communication technology
- Two-way system communication for the functions specified for this model.
- Radio signal range
- up to 2,000 m Between an integration module and a control panel (or range extender) in an open space.
- Encrypted communication
- Encrypted device communication.
- Frequency hopping
- To prevent radio interference and jamming.
Wired devices connection
- Number of zones
- 18 wired zones Multiple devices can be connected to one zone. The number of connected devices depends on their power consumption.
- Type of connection
- NC, NO, EOL MultiTransmitter Jeweller with a firmware version lower than 2.13. NC, NO, EOL, 2EOL, 3EOL 2EOL and 3EOL connection types are only available for MultiTransmitter Jeweller with the firmware version 2.13.0 or later. The integration module should be added to a compatible hub running on OS Malevich 2.13 or later. If Hub (4G) Jeweller is used, the control panel should be updated to OS Malevich 2.28 or later.
- EOL resistance
- from 1 kΩ to 7.5 kΩ with 100 Ω increment MultiTransmitter Jeweller with a firmware version lower than 2.13. EOL resistance is measured automatically in the Ajax PRO apps. from 1 kΩ to 15 kΩ for each resistor, up to 30 kΩ of total resistance MultiTransmitter Jeweller with a firmware version 2.13 and higher. Resistance is measured automatically for each EOL resistor in the Ajax PRO apps.
- Cable length
- up to 400 m When using a signal cable with a 0.22 mm² copper-clad aluminium conductor.
- Operation mode
- pulse, bistable Adjusted by a PRO or user with admin rights in the Ajax app.
- Event types
- 15 event types of wired devices Tamper alarm; Intrusion; Fire; Auxiliary alarm; Panic button; Gas alarm; Malfunction; Leakage; Glass break; High temperature; Low temperature; Masking; Duress code (opening); Vibration (seismic sensor); Custom Adjusted by a PRO or a user with admin rights in the Ajax app.
Sabotage protection
- Tamper alarm
- Two tampers to detect the MultiTransmitter Jeweller casing opening and alert about detachment from the wall.
- Protection against spoofing
- device authentication
- Communication loss detection
- within 36 seconds Between a hub or range extender and MultiTransmitter Jeweller. The detection time depends on the Jeweller or Jeweller/Fibra settings.
- Instant detection of wired connection loss, short circuits, and malfunctions
- when using EOL/2EOL/3EOL connection type Depends on the connection type.
Power supply
- MultiTransmitter Jeweller power supply
- 100–240 V~, 50/60 Hz
- Device’s operating voltage range
- 100–240 V~, 50/60 Hz
- MultiTransmitter Jeweller backup power supply
- 12 V⎓, up to 7 Ah capacity with a full charge cycle of up to 30 hours MultiTransmitter Jeweller average consumption from the backup battery after the main power supply loss is up to 33 mA (without detectors). When using a 7 Ah battery, the minimum operating time at a maximum load of 1 А will be 7 hours. For autonomous work for 12 or 24 hours, the maximum load should be no more than 0.55 A and 0.28 A, respectively.; The backup battery is not included in the set.
- Connected devices power supply
- 10.5–15 V⎓, up to 1 A of total maximum current consumption Two power lines powered by MultiTransmitter Jeweller for other devices. One power line for fire detectors.
Casing
- Dimensions
- 192 × 238 × 100 mm
- Weight of the white device
- 874 g
- Weight of the black device
- 802 g
- Operating temperature range
- from −10 °C to +40 °C
- Operating humidity
- up to 75%
- Protection class
- IP40, IK06 The new casing version of MultiTransmitter Jeweller has light guides for the integration module LED indication, while the previous version has the LED indicator on the board.
What’s in the box
- MultiTransmitter Jeweller board
- Casing
- Power cable
- Screw terminal block Adapter (only for INCERT compliance)
- 12 V⎓ battery connection cable
- Installation kit
- Quick start guide
For your installation
- Selected as part of an installer-reviewed security or automation project.
- Confirm the supported control panel, device software and regional radio version; test coverage at the final installation position.
- The device is powered from the 100–240 V~ mains and designed for indoor use only.
Find the right protection.
Transmitter Jeweller
Use a compact battery-powered module when its input and 3.3 V supply suit the device.
Takeover Module Jeweller
Compare listed legacy radio protocols with wired-zone integration.