MAKE IT YOURS
ManualCallPoint (Red).
Wireless addressable resettable button for manual fire alarm activation featuring programmable scenarios. Red-colored version.
Standards and certifications
ManualCallPoint (Red) Jeweller · MCP.R.J. Manufacturer-listed marks; regional and installation conditions apply.
A fire alarm within reach.
ManualCallPoint (Red) Jeweller defaults to Fire alarm mode. A deliberate press can activate interconnected fire-detector sirens and notify users through a compatible Ajax controller. Other alarm types and automation modes are configurable. The included key resets the button after use.
Key features. At a glance.
Fire detectors' sirens activation
when pressing the button
Resilient button mechanism
with minimum agile components to reduce the risk of failure
Up to 7 years
of battery life
Remote control and configuration
Automation scenarios
Informative in-app notifications
Up to 1,700 m1
range of communication with an Ajax hub
Alarm remains active until the button is manually released using the key
SmartBracket mounting panel
featuring tamper alarm
Transparent front lid to prevent accidental alarm activation
- 1Range is measured in open space; walls and installation conditions reduce it.
Ajax product information ↗ · ManualCallPoint (Red) Jeweller specifications ↗
Protection in real places.
Choose what a press should do.
Fire alarm by default
The red version defaults to Fire alarm mode. Depending on the controller, it can also be configured for auxiliary, panic, gas-leak, malfunction or water-leak alarms, or for an automation action.
A mode names the event raised by a person; this button does not detect smoke, gas or water. Scenario trigger and Custom action modes do not send an alarm to users or the monitoring station. Review the Local alarm only setting when configuring alarm forwarding.
Bring the alarm to the people who need it.
Sound the configured warning
In Fire alarm mode, pressing the button activates compatible fire-detector sirens when interconnection is enabled. Configured intrusion sirens can sound too. App alerts identify the device, while an enabled monitoring route sends the alarm to the operator.
A compatible connected hub or CIE and the correct system configuration are required. The button is not a standalone siren or detector.
A deliberate press. A clear indication.
Built for repeated use
Lift the transparent protective lid and press the centre. The resettable element moves inward and reveals two yellow stripes. Ajax designed the mechanism with few moving parts and specifies more than 500 presses. The included key returns the button to its ready position.
The lid helps prevent accidental presses. Confirm the configured response before testing the button.
Stay informed about the button itself.
Connection, tamper and device status
Regular exchanges with the hub keep the button’s status available in the app. The minimum polling interval is 12 seconds; connection-loss reporting depends on the configured polling and missed-packet settings. A tamper reports removal from SmartBracket or the mounting surface.
Automatic supervision helps identify faults. Complete commissioning and ongoing system checks required for the installation.
Years of operation. Replaceable batteries.
Up to 7 years
Two pre-installed CR123A batteries power the button. Ajax rates operation at up to 7 years with typical use: one press lasting one minute each week. The app reports a low battery so replacement can be planned.
More frequent activation and installation conditions affect battery life.
Understand what happened. Know where.
Notifications with a location
The app identifies the button and its room, with a time-stamped event history. Hub systems retain the 500 most recent events. Name each button clearly so an activation or fault can be traced to the right place.
The illustration is an example. Event wording and notification routes depend on the selected operating mode.
Connect an alarm with practical actions.
See the situation
A configured scenario can request images from a compatible MotionCam (PhOD) detector or show linked camera information. It helps the responsible person assess the scene after a manual alarm.
The illustrated equipment is additional to the button; each action must be configured and verified.
A secure link to your system.
Jeweller communication
Encrypted two-way radio, device authentication and frequency hopping help protect communication. The specified open-space range is up to 1,700 m between the button and a compatible hub or range extender.
Choose the matching regional radio version. Walls and interference reduce range; verify reception at the installed position.
Plan coverage around the building.
Extend a compatible hub system
ReX and ReX 2 can extend a supported hub system. ReX 2 can also use Ethernet to carry data back to the hub where radio conditions are difficult. Some hubs support up to five range extenders; check the exact hub’s capacity and device compatibility.
This diagram illustrates coverage planning, not a guaranteed distance through walls. Use the appropriate EN54 equipment and design rules for a fire control panel system.
Install, configure and verify.
Pair by QR code
Add the button to a compatible Ajax hub or control and indicating equipment (CIE), using the device QR code. Assign its room and a clear name; a CIE installation also uses a fire zone and can record a more detailed location.
Use current supported firmware and check the exact controller and regional radio compatibility.
Reset it. Keep it ready.
The key is part of the setup
After activation, insert the supplied key into the reset opening to release the button. In fire-alarm mode, an enabled interconnected detector alarm remains active until the button is reset. Check battery and fault notifications, and remove surface dust using a soft, dry wipe.
Keep the key accessible to the responsible person. Resetting can also trigger a configured automation action; review that behaviour during commissioning.
Find the right manual call point.
Compare Type4 ManualCallPoint with Red, Blue, Green, Yellow or White. See the intended system, starting mode and what happens when someone presses the button.
Compare manual call points →Every detail, in one place.
Communication
- Jeweller communication technology
- Two-way system communication for the functions specified for this model.
- Radio signal range
- up to 1,700 m Between the button and a hub (or range extender) in an open space.
- Encrypted communication
- Encrypted device communication.
- Frequency hopping
- To prevent radio interference and jamming.
Key features
- Resettable frangible element
- activates the button When the central part (frangible element) is pressed, the button depresses inward, triggering an alarm or initiating a scenario. Two yellow stripes appear at the top and bottom, indicating the device's state.
- Operating modes
- fire alarm; scenario trigger; auxiliary alarm; panic button; gas leak alarm; malfunction alert; water leak alarm With appropriate settings, it activates an alarm or controls Ajax automation devices.
- LED status indication
- fire alarm; malfunctions The LED indicator on the device enclosure lights up when a fire alarm is triggered or malfunctions are detected.
- Interconnected fire detectors alarms
- by pressing the button By pressing the frangible element, fire detectors in the system trigger the built-in sirens.
- Critical alerts
- The system can activate intrusion sirens and send audible alarm notifications to users, even if the sound is muted, the Do Not Disturb mode is on, or headphones are connected.
- Protection against accidental presses
- Lift the transparent lid to access the frangible element. The lid protects against false button presses.
- Alarm transmission to CMS
- can be disabled
Special tool (key)
- Button reset
- after pressing To reset the button, insert the special tool into the corresponding hole.
- Hole in the enclosure
- to hang on a ring from a keychain The person responsible for fire safety can carry the special tool on their keychain.
- Convenient dismantling
- The special tool opens the lock to dismantle the device from SmartBracket mounting panel.
Sabotage protection
- Tamper alarm
- Notifies on attempts to detach the button from the surface or remove it from the mounting panel.
- Protection against spoofing
- via device authentication
- Communication loss detection
- after 36 s The detection time depends on the Jeweller or Jeweller/Fibra settings.
Power supply
- Batteries
- 2 × CR123A Pre-installed. With typical use (one press lasting 1 minute per week), the batteries can last up to 7 years.
Enclosure
- Dimensions
- 102 × 104 × 39 mm
- Weight
- 214 g
- Operating temperature range
- from 0 °C to +50 °C
- Operating humidity
- up to 80%
What’s in the box
- ManualCallPoint (Red) Jeweller
- SmartBracket mounting panel
- Special tool (key)
- 2 × CR123A battery (pre-installed)
- Installation kit
- Quick start guide
For your installation
- Confirm the supported control panel, device software and regional radio version; test coverage at the final installation position.
- It is recommended to install the button in easily accessible places at a height of 1.4 m.; ; The device is designed for indoor installation only.
Product documents.
Find the right protection.
ManualCallPoint Jeweller
Compare the intended use and default settings of the red and coloured versions before selecting your button.
FireProtect 2 (Heat/Smoke) Jeweller
Explore the FireProtect 2 RB detector as part of a compatible planned system.