MAKE IT YOURS
Superior MotionProtect Plus G3 Fibra.
Wired IR motion detector with an additional K-band microwave sensor and anti-masking system
Standards and certifications
Superior MotionProtect Plus G3 Fibra · MPP.G3.F. Manufacturer-listed marks; regional and installation conditions apply.
Verify movement. Guard against interference.
Superior MotionProtect Plus G3 Fibra checks infrared motion with a K-band microwave sensor before reporting an alarm. Mirror optics monitor the room, while anti-masking and three tamper switches supervise attempts to interfere with the detector. Fibra provides a wired connection for power, events and remote configuration.
Key features. At a glance.
Horizontal viewing angle: 90°
Vertical viewing angle: 71°
Up to 15 m
movement detection distance
Reduced blind zone
to detect a person crawling at a distance of 50 cm from the device
Dual motion detection technology
to trigger the device only when both sensors detect motion
Software algorithm to prevent false alarms
Temperature compensation
for effective detection in the heat and in the cold
Advanced anti-masking system
K-band microwave sensor
is activated when a PIR sensor is triggered
Power adjustment
Informative push notifications
Up to 2,000 m1
range of communication with an Ajax hub or a module that extends the Fibra line
Lock
to secure the detector on a SmartBracket mounting panel
Remote control and configuration
Two colors
of matte enclosure
- 1When U/UTP cat.5, 4 × 2 × 0.51 cable is used. Other cable types may have different values. Please use the Fibra power supply calculator to check the wired system project before installing the device.
Ajax product information ↗ · Superior MotionProtect Plus G3 Fibra specifications ↗
Protection in real places.
Superior MotionProtect Plus G3 Fibra
Every detail has a purpose.
Explore the function, installation and system requirements of Superior MotionProtect Plus G3 Fibra.
Loading detail…
See the room and the approach below.
Up to 15 m of motion detection
The PIR sensor and mirror optics detect indoor movement at up to 15 m when installed at 2.4 m. The exact specification lists a reduced blind zone of 50 cm, helping detect a crawling person close to the device.
Detection depends on position and a clear view. Walk-test the actual intrusion path and nearby floor area after installation.
A second sensor verifies movement.
PIR detection, checked by K-band
The PIR sensor detects changes in infrared radiation; the microwave sensor verifies that movement is present. The combined decision helps filter thermal interference, such as air flows and heating effects, before the detector reports an alarm.
This is motion verification, not photo or video verification. The detector has no camera.
Filter thermal interference.
SmartDetect analyses the moving heat pattern
The algorithm assesses infrared intensity, the shape and size of a warm object, movement and time in the detection area. It helps distinguish a person from environmental thermal changes.
Cover the room, including the approach below.
Position the mirror optics across the entry path
Install indoors at 2.4 m, looking across the likely movement path. The mirror optics provide a 90° horizontal and 71° vertical field of view. Keep furniture, plants and glass outside the monitored view, then walk-test the full room.
Choose G3 with its detection priorities in mind
These detectors do not support pet immunity. Their reduced blind zone is intended to recognise movement close below the device, including a crawling person. Plan the protected area so animals cannot enter it while armed.
Do not apply the 20 kg / 50 cm pet-immunity limits of other MotionProtect models to these G3 devices.
Use in a suitable indoor environment
The operating range is −10 to +40 °C with humidity up to 75%. Avoid direct sunlight, heat sources and obstructions close to the optics. An IP30 enclosure is for indoor use; check detection again after changing the room layout.
Notice when someone blocks the view.
Keep anti-masking enabled and calibrated
The dedicated sensor detects attempts to obstruct or cover the optics, including material placed over the detector or paint on its window. With anti-masking enabled, this protection also operates while the system is disarmed.
Calibrate in the final mounting position with a clear field of view. Recalibrate after moving the detector or when the app reports a calibration fault, and test masking detection before handover.
Protect the mounting as well as the room.
Three tamper switches and a monitored lock
Two rear tamper switches supervise the mounting, while a third monitors the SmartBracket lock. Wall and side mounting depend on the correct fixing points and intact breakaway sections. Lock the detector in place and test removal events after installation.
A tamper alert identifies interference; it does not physically prevent damage. Confirm that the app and any monitoring service receive the event.
Check the detector as well as its connection.
Supervise the built-in sensors
Automatic self-tests check the PIR and masking sensors and the microwave sensor. Faults appear in the app, and a manual test is available during commissioning and maintenance.
A wired connection to the whole system.
Fibra carries power and events
A four-core Fibra cable connects the detector to a compatible wired Ajax hub. Two-way communication, encrypted data and device authentication help protect the connection. The detector has no camera and requires the hub to manage the system.
Up to 2,000 m on a beam with U/UTP cat.5 4 × 2 × 0.51 mm (24 AWG) copper cable, subject to the complete cable and load calculation. Check the selected hub, topology and firmware; a ring has different limits.
Plan the complete line load.
7–30 V DC from the Fibra line
The four-core line supplies the detector, with 24 V DC nominal operation. There is no replaceable detector battery; reserve operation depends on the hub and any powered modules in the route.
The current specification gives 4.3 mA quiescent and 11.6 mA maximum at 24 V DC. Use the exact model in the Fibra power calculator.
Connect the line. Calibrate the detector.
Wire through the removable terminal board
An accredited Ajax partner plans the cable route and switches off line power before wiring. The removable terminal board and built-in level support wall or side installation without dismantling the detector enclosure. Fit permanent fasteners and close the monitored SmartBracket lock.
Find the right motion detector.
Compare indoor, outdoor and curtain detectors across Baseline and Superior. See what changes for the place you protect, alarm photos, animals and installation.
Compare motion detectors →Every detail, in one place.
Communication
- Fibra communication technology
- Proprietary wired communication technology to transmit commands, alarms, and events. Key features: Two-way communication. Advanced anti-sabotage. Instant notifications. Remote control and configuration in Ajax apps.
- Line connection
- 4-core cable
- Connection
- to any point of the Fibra line The device can be installed behind the hub, detector, keypad, or siren.
- Fibra line length
- up to 2,000 m When using the U/UTP cat.5 twisted pair cable.
- Encrypted communication
- All stored and transmitted data are protected by block encryption featuring a dynamic key.
Detection
- Sensitive elements
- 1 × PIR sensor 1 × K-band microwave sensor Operating frequency: 24 GHz.
- Motion detection distance
- up to 15 m When installed at a height of 2.4 m.
- Reduced blind zone
- up to 0.5 m Detects a crawling person at a distance of 50 cm from the detector.
- Motion detection angles
- horizontal: 90° vertical: 71°
- Motion detection speed
- from 0.1 to 4.0 m/s The direction of the detector sensors should be perpendicular to an alleged intrusion path into the facility.
- False alarm prevention
- Dual motion detection technology SmartDetect Software algorithm.
- Temperature compensation
- Effective motion detection at temperatures from −10 °C to +40 °C.
- Self-test of sensitive elements
- The device checks its sensors’ state and notifies if any malfunction is detected.
Sabotage protection
- Tamper alarm
- 3 tampers Notifications on attempts to detach the detector from the surface or unlock the SmartBracket lock and remove the detector from the mounting panel.
- Protection against spoofing
- device authentication
- Anti-masking system
- detects attempts to block the detector view
- Lock for SmartBracket
- To secure the detector on SmartBracket.
- Communication loss detection
- after 36 s Detection time depends on the Jeweller/Fibra settings.
Power supply
- Operating voltage range
- 7−30 V⎓ The hub powers the detector via the Fibra line.
- Nominal operating voltage
- 24 V⎓
- Quiescent current consumption at nominal voltage
- 4.3 mA
- Maximum current consumption at nominal voltage
- 11.6 mA
Enclosure
- Dimensions
- 120 × 62 × 52 mm
- Weight
- 156 g
- Operating temperature range
- from −10 °C to +40 °C
- Operating humidity
- up to 75%
- Protection class
- IP30
What’s in the box
- Superior MotionProtect Plus G3 Fibra
- SmartBracket mounting panel
- Installation kit
- Quick start guide
For your installation
- Selected as part of an installer-reviewed security or automation project.
- Fibra needs a supported hybrid control panel, checked cable type and topology, termination and a complete power budget. Existing alarm cabling is not automatically suitable.
- It is recommended to install the detector at a height of 2.4 m.
- The pet immunity feature is not available for this device.
- The device is designed for indoor use only.
Product documents.
Find the right protection.
Superior MotionProtect G3 Fibra
Check whether PIR detection or additional microwave verification suits the room.
Superior MotionProtect Plus G3 Jeweller
Explore the corresponding wired or wireless model and its own requirements.