MAKE IT YOURS
FireProtect 2 (Heat/Smoke).
A loud local siren in the room. Phone notifications with a compatible connected system.
Standards and certifications
* Ajax shows these marks for the FireProtect 2 (Heat/Smoke) Jeweller range. Check the linked documentation for the exact version and market.
Two signs of fire. One local alarm.
FireProtect 2 (Heat/Smoke) Jeweller combines optical smoke detection with two heat sensors. A built-in siren warns people nearby, while a compatible Ajax hub adds app notifications and coordinated alarms. The RB version uses replaceable batteries. This version detects smoke and heat; it does not contain a CO sensor.
Key features. At a glance.
Two types of interconnected fire alarm1
Primary: via an Ajax hub, alarm within 20 s
Replaceable batteries
RB version · two replaceable CR123A batteries
Sensors
Heat
Smoke
Remote control and configuration
85 dB built-in siren
Informative push notifications
Up to 1,700 m2
Communication range with an Ajax hub in open space
Power adjustment
Two colors
Hassle-free installation
Operates as part of the Ajax system or as a standalone device
SmartBracket
with an adjustable rotation angle
Dual-spectrum optical smoke sensor
to filter out false alarms
Dustproof and insect-resistant smoke chamber
- 1Requires supported detector hardware/firmware, hub version, configuration and tested radio coverage. See the interconnection section for the applicable conditions.
- 2Range is measured in open space; walls and installation conditions reduce it.
Ajax product information ↗ · FireProtect 2 RB (Heat/Smoke) Jeweller specifications ↗
Protection in real places.
FireProtect 2 (Heat/Smoke) Jeweller
Every detail has a purpose.
Explore smoke and heat detection, audible warning and battery choice.
Loading detail…
Smoke detection with a closer look at the particles.
Dual-spectrum optics and HazeFlow 2
Blue and infrared light help the optical sensor analyse particles in the smoke chamber. HazeFlow 2 evaluates the readings to distinguish smoke from interference such as steam. The chamber is designed to resist dust and insects.
Correct placement remains essential. A smoke detector should not be exposed to routine fumes, steam or airflow that can interfere with detection.
Detect a high temperature or a sudden rise.
Two A1R-class thermistors
Two thermistors monitor temperature outside the enclosure. The detector raises a heat alarm above +64 °C or when temperature rises by more than 10 °C within one minute.
These alarm conditions apply to the European model. Choose the sensor combination and installation position for the room; heat detection does not replace required smoke coverage.
A local alarm, with a clear device status.
85 dB sound and LED indications
The built-in siren is rated at 85 dB at 3 m. Sound patterns and LEDs distinguish an alarm from a fault, low battery or end of life. With a compatible connected hub, configured app notifications identify the detector and its room.
The detector monitors its own sensors even when the intrusion system is disarmed. As a standalone detector it provides local warnings; app notifications and remote settings require a hub.
Spread the alarm through the property.
Primary interconnection through the hub
When an enabled detector reports an alarm, a compatible Ajax hub can activate the other fire detectors in the system within 20 seconds. The actual number of devices depends on the hub and system configuration.
A direct fallback between detectors
Supported FireProtect 2 RB units can also pass the alarm directly to other detectors within 60 seconds. This second path operates alongside the hub path and can continue when the hub connection is lost.
Requires detectors marked “Fallback interconnect supported”, compatible 5.59.2-series firmware, OS Malevich 2.19 or later and the fallback setting enabled. Hub (4G) requires 2.28 or later. For smoke-sensing models, use firmware 5.59.2.9 or later; check the exact detector revision before setup. Run the coverage test after setup.
Replace the batteries when needed.
Two replaceable CR123A batteries
The RB version uses two pre-installed CR123A batteries, with up to 7 years of operation. Replace both batteries as instructed when a low-battery warning appears, then run the detector test.
Battery Life Optimization must be enabled for the stated lifetime; settings, radio conditions and alarm use affect it. The detector itself has a 10-year service life; new batteries do not reset it.
Connect the detector to the rest of the system.
Jeweller two-way radio
Jeweller carries alarms and device states to a compatible Ajax hub or range extender. The radio protocol uses encryption, device authentication, frequency hopping and automatic power adjustment. The specified range is up to 1,700 m in open space; walls and interference reduce it.
Check the hub and detector revision.
Model-specific compatibility
Requires OS Malevich 2.14.1 or later for supported hubs; Hub (2G) requires 2.15.4 or later and Hub (4G) requires 2.28 or later. These are minimum firmware conditions, not a statement that every hub is supported. Consult the exact-model compatibility list before adding the device. Fallback interconnection has its own requirements listed above.
Add context to an alarm.
An optional photo scenario
A separate compatible MotionCam (PhOD) detector can take photographs after a configured FireProtect 2 alarm. A suitable hub, photo permissions and the scenario must be set up in advance. This FireProtect 2 detector has no built-in camera.
Separate automation devices can also support a professionally planned response, such as controlling appropriate circuits or door hardware. Photos and scenarios do not replace the required alarm response.
Set up the detector for its actual room.
Choose and secure the position
Use the installation instructions for this sensor combination. Check the permitted room conditions, clearances and mounting position before fixing SmartBracket. Its 90° rotation adjustment helps align the enclosure after mounting.
Indoor use only: 0 to +50 °C, up to 80% humidity and IP20. A photograph of a room is an application example, not a substitute for the placement requirements.
Test it. Keep it ready.
Test/Mute on the front panel
Press the centre of the front panel to use Test/Mute. Follow the manual to run the self-test, and confirm that the sound and light indications work. Testing is also available through the app when the detector is connected to a compatible hub.
Test after installation and battery replacement, then follow the required regular testing schedule. A self-test does not remove the need to maintain the installation.
Act on maintenance warnings
Check and respond to low-battery, fault and end-of-life indications. Keep the enclosure clean as described in the manual and replace the detector at the end of its 10-year service life.
Find the right fire detector.
Compare what each FireProtect detects, how it is powered and what you will need to maintain. Choose the sensor combination for the hazards in the room.
Compare fire detectors →Every detail, in one place.
Communication
- Jeweller communication technology
- Two-way system communication for the functions specified for this model.
- Radio communication range
- up to 1,700 m Between the detector and a hub (or radio signal range extender) in an open space.
- Encryption of radio communication
- All the data stored and transmitted are protected by block encryption with a floating key.
- Radio frequency hopping
- To prevent radio interference and jamming.
Sensitive elements
- Sensitive elements
- smoke sensor; heat sensor
Smoke detection
- Sensitive element
- double-spectrum optical sensor Recognizes smoke by the size of particles in the air.
- Protection from false alarms
- Does not react to water vapor.
- Patented smoke chamber
- Protects the smoke sensor from dust, dirt, and insects.
Dangerous temperature detection
- Sensitive element
- according to the requirements for Class A1R heat detectors Requirements of EN 54-5 and BS 5446-2 standards.
- High temperature alarm
- at temperatures above 64°C
- Temperature spike alarm
- when the temperature rises more than 10°C in 1 minute or less
Additional features
- In-built siren
- volume 85 dB at a distance of 3 meters Sound notification of alarms. Active until the reason for triggering is eliminated or until the user disables notification.
- Interconnected fire detectors alarms
- via primary interconnection If one of the fire detectors in the system detects a threat, it sends an alarm to the hub. Within 20 seconds, the hub initiates an interconnected alarm and sends data to Ajax apps. via fallback interconnection1 At the same time with notifying the hub, the initiating detector sends an alarm directly to other detectors. All connected detectors activate the buzzer within a minute. It will work even in the worst-case scenario of losing connection with the hub. 1 Fallback interconnected alarm is available only for FireProtect 2 detectors with firmware version 5.59.2.ХХ or later. Devices that support the fallback interconnected alarm are marked on the package with a “Fallback interconnect supported” label.
- LED indication
- green is a power indication A LED indicator on the device enclosure lights up once every 56 seconds. The indication meets the requirements of EN 50291. yellow is an indication of malfunctions A LED indicator on the device enclosure lights up when malfunctions are detected. For example, in the case of discharged batteries, contamination of the smoke chamber, or end of the service life. red is an indication of fire alarms A LED indicator on the device enclosure lights up when the detector registers a fire alarm.
- Button on the front panel of the detector
- In normal mode, when pressed, it starts the smoke chamber test. In the event of an alarm or malfunction, the pressing turns off the detector sound notification.
Anti-sabotage protection
- Tampering alarm
- Alerts of attempts to detach the detector from the surface or remove the mounting panel.
- Protection against spoofing
- device authentication
- Detection of communication failure
- within 15 minutes The time to detect communication loss depends on the settings for the number of undelivered data packages (specified in the Jeweller or Jeweller/Fibra settings). The polling interval is fixed at 300 seconds.
Power supply
- For FireProtect 2 RB (Heat/Smoke)
- 2 × CR123A battery Up to 7 years of battery life.
Enclosure
- Dimensions
- 124 × 124 × 45 mm
- Weight
- 272 g
- Operating temperature range
- from 0°С to +50°С
- Operating humidity
- up to 80%
- Protection class
- IP20
What’s in the box
- FireProtect 2 RB (Heat/Smoke) Jeweller
- SmartBracket mounting panel
- Installation kit
- 2 × CR123A battery (pre-installed)
- Quick start guide
For your installation
- Connected features require a compatible Ajax system, and app permissions per user.
- Choose the sensor combination for the room. This page offers RB with replaceable batteries; mains-powered AC models are separate products.
- This is a Residence-line detector. Where an EN54 fire system is required, that is a separate designed system rather than an accessory to this detector.
Optional additions
Product documents.
Find the right protection.
Hub 2 Plus Jeweller
Explore hub connectivity and capacity, then verify this detector’s compatibility and firmware.
FireProtect 2 (CO) Jeweller
Review a different sensor combination for the rest of the property.